555 Timer Calculator

This 555 timer calculator works out the output of the classic NE555 circuit. In astable mode enter R1, R2 and C to get the frequency, duty cycle and high and low times, or enter a target frequency to find R2. In monostable mode enter R and C for the pulse width. Values can be typed as 4.7k, 100n or 10µ. Paste a list of component combinations to compare them. It runs in your browser.

Example astable values

R1R2CFrequencyDuty
1 kΩ10 kΩ10 µF6.87 Hz52.4%
10 kΩ68 kΩ10 µF0.99 Hz53.4%
1 kΩ6.8 kΩ100 nF988 Hz53.4%
4.7 kΩ4.7 kΩ1 µF102 Hz66.7%
1 kΩ1 kΩ10 nF48.1 kHz66.7%

When to use it

  1. Design an LED flasher or blinker.
  2. Make a tone generator at a set pitch.
  3. Build a clock for a counter or logic circuit.
  4. Set a one-shot delay for a relay or debounce.
  5. Check a circuit's timing from its parts.

How to Use

  1. Choose astable or monostable.
  2. Enter R1, R2 and C (or R and C).
  3. Read frequency, duty cycle and timings.
  4. Paste a list of values to compare circuits.

Features

  1. Astable frequency and duty cycle
  2. High and low times
  3. Monostable pulse width
  4. R2 for a target frequency
  5. Engineering notation
  6. Batch CSV
  7. 100% client-side

FAQs

How do I calculate 555 frequency?

f = 1.44 ÷ ((R1 + 2R2) × C). With R1 = 1 kΩ, R2 = 10 kΩ and C = 10 µF it is about 6.9 Hz.

Why can't I get a 50% duty cycle?

The high time includes R1, so it is always longer than the low time. Add a diode across R2 or use a CMOS 555 trick to get 50% or less.

What is the monostable pulse width?

t = 1.1 × R × C. 100 kΩ and 10 µF gives about 1.1 seconds.

How accurate is it?

Capacitor tolerance dominates; electrolytics can be ±20%, so use film capacitors for precise timing.

Is anything uploaded?

No. Everything runs in your browser.

Technical Details

Astable mode: the capacitor charges through R1 + R2 and discharges through R2, so high time = ln 2 × (R1 + R2) × C, low time = ln 2 × R2 × C, frequency = 1.44 ÷ ((R1 + 2R2) × C) and duty cycle = (R1 + R2) ÷ (R1 + 2R2). Monostable mode: pulse width = 1.1 × R × C. Given a target frequency, R1 and C, R2 = (1.44 ÷ (f × C) − R1) ÷ 2. Values accept engineering notation (4k7, 100n, 10µ). Batch mode reads R1, R2 and C per row; a blank R2 means monostable.

Electronics Tools

Electronics Tools

  • Op-Amp Gain Calculator
  • RC and RL Filter / Time Constant Calculator
  • PCB Trace Width Calculator (IPC-2221)
  • SMD Resistor Code Decoder
  • dBm, mW and Volts Converter
  • Antenna Length Calculator
  • PoE Power Budget Calculator
  • Ohm's Law Calculator