Bolt Torque and Preload Calculator

This bolt torque calculator gives the tightening torque and clamp load for a bolt from its size, strength and lubrication. Choose metric (M3–M36, classes 4.6 to 12.9) or inch (UNC/UNF, SAE grades 2, 5 and 8), the lubrication condition and the preload you want as a share of proof load, and it shows the torque in N·m and lb·ft, the clamp force and the proof load. Paste a list of bolts for a joint or a whole machine. It runs in your browser.

Metric coarse, dry (K 0.20), 75% of proof load

Size8.8 torque10.9 torque8.8 clamp
M610.5 N·m15.0 N·m8.8 kN
M825.5 N·m36.5 N·m15.9 kN
M1050.5 N·m72.2 N·m25.2 kN
M1288.0 N·m126 N·m36.7 kN
M16218 N·m312 N·m68.2 kN
M20441 N·m610 N·m110 kN
M24761 N·m1,053 N·m159 kN

When to use it

  1. Torque flange bolts to a consistent clamp load.
  2. Make a torque chart for a maintenance manual.
  3. See how lubrication changes the right torque.
  4. Compare 8.8 and 10.9 bolts for a joint.
  5. Check a torque value from a drawing.

How to Use

  1. Choose metric or inch and the bolt size.
  2. Choose the property class or grade.
  3. Choose lubrication and preload %.
  4. Read torque and clamp load; paste a bolt list.

Features

  1. Metric classes 4.6–12.9
  2. SAE grades 2, 5, 8
  3. Nut factor by lubrication
  4. Clamp load and proof load
  5. N·m and lb·ft
  6. Batch CSV
  7. 100% client-side

FAQs

What torque for an M10 8.8 bolt?

About 50 N·m dry (K = 0.2) at 75% of proof load; lubricated, around 37–45 N·m.

What is the nut factor K?

An experimental factor covering thread and underhead friction: about 0.20 dry, 0.15–0.18 oiled, 0.10–0.12 with moly or anti-seize.

Why use 75% of proof load?

It gives a high clamp while leaving margin for reuse; 90% is used for permanent joints.

Should I follow a manufacturer's torque instead?

Yes. Where the equipment maker specifies a torque, use that.

Is anything uploaded?

No. Everything runs in your browser.

Technical Details

Torque T = K × d × F. The target preload F is a percentage (typically 75% for reusable joints, 90% for permanent ones) of the proof load: proof strength × tensile stress area. Proof strengths follow ISO 898-1 (4.6: 225 MPa, 5.8: 380, 8.8: 580 up to M16 and 600 above, 10.9: 830, 12.9: 970) and SAE J429 (grade 2: 55 ksi, grade 5: 85 ksi, grade 8: 120 ksi). Tensile stress area is (π/4)(d − 0.9382P)² for metric and 0.7854(D − 0.9743/n)² for inch threads. K ranges from about 0.20 dry to 0.10 with anti-seize.

Calculators & Converters

Calculators & Converters

  • Tap Drill and Thread Chart
  • ISO Fits and Tolerances Calculator
  • Spur Gear Calculator
  • Pulley and Belt Calculator
  • Spring Rate Calculator
  • Hydraulic Cylinder Force Calculator
  • Pipe Flow and Pressure Drop Calculator
  • Psychrometric Calculator