UPS & Inverter Backup Time Calculator

This UPS backup time calculator tells you how long your inverter battery will run your fans, lights and router during load-shedding. Enter the battery's Ah and voltage, how many batteries are wired in series, the battery type and the inverter's efficiency, then build the load from a list of common appliances or your own wattages. The result shows the backup in hours and minutes, the usable energy after a safe depth of discharge (50% for lead-acid, 70% for tubular, 90% for lithium), and the current drawn from the battery, with a warning when a lead-acid bank is pushed too hard to deliver its rated capacity. Set a target number of hours and it works out the Ah you need instead. To compare several batteries before buying, paste a CSV of options and each one is calculated side by side. It is free, runs in your browser, and nothing you enter is uploaded.

Approximate backup on one 12 V battery (85% efficiency)

BatteryUsable Wh150 W load300 W load500 W load
150 Ah lead-acid (50%)7655 h 6 min2 h 33 min1 h 32 min
200 Ah tubular (70%)1,4289 h 31 min4 h 46 min2 h 51 min
100 Ah LiFePO4, 12.8 V (90%)9796 h 32 min3 h 16 min1 h 58 min

When to use it

  1. Find out whether one 200 Ah tubular battery will last a four-hour outage.
  2. Size a battery for two fans, four lights and a router overnight.
  3. Compare a lead-acid, a tubular and a lithium battery before buying.
  4. Decide whether to add a second battery in series to a 24 V inverter.
  5. Check how much backup an old UPS has left after adding a TV to the load.

How to Use

  1. Enter the battery Ah, voltage and number in series.
  2. Choose the battery type and inverter efficiency.
  3. Add your appliances and quantities to build the load.
  4. Read the backup time, or set a target to see the Ah you need; paste a CSV to compare options.

Features

  1. Backup time in hours and minutes
  2. Lead-acid, tubular and lithium presets
  3. Appliance load builder
  4. Battery Ah needed for a target
  5. Battery current and C-rate warning
  6. CSV comparison of battery options
  7. 100% client-side

FAQs

How do I calculate UPS backup time?

Multiply battery Ah × voltage × number of batteries × depth of discharge × inverter efficiency, then divide by the load in watts.

How long will a 200 Ah battery last?

A 12 V 200 Ah tubular battery at 70% depth of discharge and 85% efficiency gives about 4 hours 45 minutes on a 300 W load.

Why is real backup shorter than calculated?

Older batteries hold less than their rating, and lead-acid batteries deliver less than their rated Ah at high current. Keep the C-rate below 0.2 for a closer match.

What depth of discharge should I use?

About 50% for flooded or AGM lead-acid, 70% for tubular and 80–90% for LiFePO4 lithium, to protect cycle life.

Is anything saved?

No. The calculator runs in your browser and nothing is sent anywhere.

Technical Details

Stored energy is battery Ah × voltage × number of batteries in series. Usable energy multiplies that by the depth of discharge that preserves cycle life (50% for flooded or AGM lead-acid, 70% for tubular, 90% for LiFePO4) and by the inverter's efficiency. Backup hours are usable Wh ÷ total load in watts, where the load is the sum of each appliance's watts × quantity. Battery current is load ÷ efficiency ÷ bank voltage, and the C-rate (current ÷ Ah) flags lead-acid loads above 0.2C, where Peukert's effect makes real capacity fall short of the 20-hour rating. A reverse panel solves for the Ah needed per battery to reach a target number of hours. Batch mode compares battery options row by row.

Electronics Tools

Electronics Tools

  • Solar System Sizer
  • Voltage Drop & Wire Size Calculator
  • Cable Ampacity and Derating Calculator
  • Conduit Fill Calculator
  • AWG to mm² Wire Gauge Converter
  • Three-Phase Power Calculator
  • Power Factor Correction Calculator
  • Transformer kVA and Full-Load Current Calculator